View AAT1154IAS-10-T1_1158690.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1MHz 3A Step-Down DC/DC Converter General Description
The AAT1154 SwitchReg is a step-down switching converter ideal for applications where high efficiency, small size, and low ripple are critical. Able to deliver 3A with an internal power MOSFET, the current-mode controlled IC provides high efficiency. Fully internally compensated, the AAT1154 simplifies system design and lowers external parts count. The AAT1154 is available in a Pb-free SOP-8 package and is rated over the -40C to +85C temperature range.
AAT1154
Features
* * * * * * * * * * * * * *
SwitchRegTM
VIN Range: 2.7V to 5.5V Fixed or Adjustable VOUT: 1.0V to 4.2V 3A Output Current Up to 95% Efficiency Integrated Low On Resistance Power Switch Internally Compensated Current Mode Control 1MHz Switching Frequency Constant Pulse Width Modulation (PWM) Mode Low Output Ripple With Light Load Internal Soft Start Current Limit Protection Over-Temperature Protection SOP-8 Package -40C to +85C Temperature Range
Applications
* * * * * Cable/DSL Modems Computer Peripherals High Efficiency Conversion from 5V or 3.3V Supply Network Cards Set-Top Boxes
Typical Application
INPUT VP FB
10F 100
AAT1154
VCC LX
1.5H
EN 0.1F GND 120F OUTPUT
1154.2006.09.1.6
1
1MHz 3A Step-Down DC/DC Converter Pin Descriptions
Pin #
1
AAT1154
Symbol
FB
Function
Feedback input pin. This pin must be connected to the converter output. It is used to set the converter output to regulate to the desired value. Ground connection. Enable input pin. When connected high, the AAT1154 is in normal operation; when connected low, it is powered down. This pin should not be left floating. Power supply: supplies power for the internal circuitry. Input supply voltage for converter power stage. Inductor connection pins. These pins should be connected to the output inductor. Internally, Pins 6 and 7 are connected to the drain of the P-channel switch.
2 3
GND EN
4 5, 8 6, 7
VCC VP LX
Pin Configuration
SOP-8
FB GND EN VCC
1
8
VP LX LX VP
1
2
2
7
3
6
4
5
2
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter Absolute Maximum Ratings1
TA = 25C, unless otherwise noted. Symbol
VCC, VP VLX VFB VEN TJ VESD
AAT1154
Description
VCC, VP to GND LX to GND FB to GND EN to GND Operating Junction Temperature Range ESD Rating2 - HBM
Value
6 -0.3 to VP + 0.3 -0.3 to VCC + 0.3 -0.3 to VCC + 0.3 -40 to 150 3000
Units
V V V V C V
Thermal Characteristics3
Symbol
JA PD
Description
Thermal Resistance Maximum Power Dissipation (TA = 25C)4
Value
110 909
Units
C/W mW
Recommended Operating Conditions
Symbol
T
Description
Ambient Temperature Range
Rating
-40 to +85
Units
C
1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. 3. Mounted on a demo board (FR4, in still air). 4. Derate 9.1mW/C above 25C. 1154.2006.09.1.6
3
1MHz 3A Step-Down DC/DC Converter Electrical Characteristics
VIN = VCC = VP = 5V, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = 25C. Symbol
VIN VOUT VUVLO VUVLO(HYS) IQ ISHDN ILIM RDS(ON)H VOUT (VOUT*VIN) VOUT/VOUT FOSC VEN(L) VEN(H) TSD THYS
AAT1154
Description
Input Voltage Range Output Voltage Tolerance Under-Voltage Lockout Under-Voltage Lockout Hysteresis Quiescent Supply Current Shutdown Current Current Limit High Side Switch On Resistance Efficiency Load Regulation Line Regulation Oscillator Frequency Enable Threshold Low Enable Threshold High Over-Temperature Shutdown Threshold Over-Temperature Shutdown Hysteresis
Conditions
VIN = VOUT + 0.2V to 5.5V, IOUT = 0A to 3A VIN Rising VIN Falling No Load, VFB = 0V VEN = 0V, VIN = 5.5V TA = 25C TA = 25C IOUT = 1A ILOAD = 0A to 3A VIN = 2.7V to 5.5V TA = 25C
Min
2.7 -5.0 1.2
Typ Max Units
5.5 5.0 2.5 250 630 V % V mV A A A m % % %/V MHz V V C C
1000 1.0
4.4 60 92 2.6 0.75 1 0.6 1.4 140 15
4
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter Typical Characteristics
Efficiency vs. Load Current
(VIN = 5V; VOUT = 3.3V)
100 95
AAT1154
RDS(ON) vs. Temperature
90 80
Efficiency (%)
90
VIN = 2.7V VIN = 3.6V
VIN = 4.2V
RDS(ON) (m)
85 80 75 70 65 60 0.01 0.1 1 10
70 60 50 40 -20 0 20 40 60 80 100 120
VIN = 5.5V VIN = 5V
Output Current (A)
Temperature (C)
Oscillator Frequency Variation vs. Supply Voltage
0.5 70 65
RDS(ON) vs. VIN
(IDS = 1A)
RDS(ON) (m)
Variation (%)
0.25
60 55 50 45 40
0
-0.25
-0.5 3.5 4 4.5 5 5.5
2.5
3
3.5
4
4.5
5
5.5
Input Voltage (V)
Input Voltage (V)
Oscillator Frequency Variation vs. Temperature
(VIN = 5V)
Enable Threshold (V)
1 0 1.2 1.1 1 0.9 0.8 0.7 0.6 -20 0 20 40 60 80 100
Enable Threshold vs. Input Voltage
EN(H)
Variation (%)
-1 -2 -3 -4
EN(L)
2.5 3 3.5 4 4.5 5 5.5
Temperature (C)
Input Voltage (V)
1154.2006.09.1.6
5
1MHz 3A Step-Down DC/DC Converter Typical Characteristics
Output Voltage vs. Temperature
(IOUT = 2A)
0.4 1
AAT1154
Line Regulation
(VOUT = 3.3V)
Output Voltge Error (%)
0.2
Variation (%)
0 -1 -2 -3 -4 -5 3
IO = 0.3A
0 -0.2 -0.4 -0.6 -0.8 -20 0 20 40 60 80 100
IO = 3.0A
3.5
4
4.5
5
5.5
6
Temperature (C)
Input Voltage (V)
Over-Temperature Current vs. Input Voltage
(VOUT = 3.3V)
3.6
0.0 -1.0
Load Regulation
(VIN = 5.0V; VIN = 3.3V)
Output Current (A)
3.4 3.2 3 2.8 2.6 2.4 2.2
Output Error (%)
70C
-2.0 -3.0 -4.0 -5.0 -6.0 -7.0 -8.0 -9.0 -10.0
85C 100C
3.5 3.75 4 4.25 4.5 4.75 5 5.25 5.5
2
0.01
0.1
1
10
Input Voltage (V)
Load Current (A)
Non-Switching Operating Current vs. Temperature
(FB = 0V)
0.8
Over-Temperature Shutdown Current vs. Temperature
(VOUT = 3.3V; VIN = 5.0V; L = 1.5H)
6 5.5 5 4.5 4 3.5 3 2.5 2 10 20 30 40 50 60 70 80 90 100
Operating Current (mA)
VIN = 5.5V
0.7
VIN = 5.0V
0.6
0.5
VIN = 2.7V
-20 0 20
VIN = 3.6V
VIN = 4.2V
0.4 40 60 80 100 120
Output Current (A)
Temperature (C)
Temperature (C)
6
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter Typical Characteristics
Inrush and Output Overshoot Characteristics
(3A Load)
14 12 6 4 2 0
AAT1154
Inrush and Output Overshoot Characteristics
(No Load)
14 12 6
Inductor Current
Inductor Current
4 2 0 -2
Inductor Current (A) (top trace)
Inductor Current (A) (top trace)
Voltage (V) (bottom traces)
Voltage (V) (bottom traces)
10 8 6 4 2 0 -2 0 0.4 0.8 1.2 1.6 2
10 8 6 4 2 0 -2 0 0.4 0.8 1.2 1.6 2
Input Output
-2 -4 -6 -8 -10
Input Output
-4 -6 -8 -10
Time (ms)
Time (ms)
Output Ripple
(IOUT = 3.0A; VOUT = 3.3V; VIN = 5.0V)
4 2 7 6 4 2
Output Ripple
(IOUT = 3.0A; VOUT = 3.3V; VIN = 5.0V)
7 6
AC Output Ripple top (mV)
AC Output Ripple (top) (mV)
Inductor Current (bottom) (A)
Inductor Current (bottom) (A)
0 -2 -4 -6 -8 -10 -12 0 1 2 3 4 5
5 4 3 2
0 -2 -4 -6 -8 -10 -12 0 1 2 3 4 5
5 4 3 2
300F 6.3VCeramic TDK P/N C3325X5R0J107M
1 0 -1
200F 6.3V Ceramic TDK P/N C3325X5R0J107M
1 0 -1
Time (s)
Time (s)
Tantalum Output Ripple
(IOUT = 3.0A; VOUT = 3.3V; VIN = 5.0V)
16
Loop Crossover Gain and Phase
180 135
AC Output Ripple (top) (mV)
40 20 0 -20 -40 -60 -80 -100 -120 0 1 2 3 4 5
7 6
12 8
Gain (dB)
5 4 3 2
Phase 3x 100F 2x 100F 100F 6.3V Ceramic TDK P/N C3225X5R0J107M
90 45 0 -45 -90 -135 -180 100000
Phase (degrees)
Inductor Current (bottom) (A)
4 0 -4 -8 -12
120F 6.3V Tantalum Vishay P/N 594D127X96R3C2T
1 0 -1
-16 10000
Time (s)
Frequency (Hz)
1154.2006.09.1.6
7
1MHz 3A Step-Down DC/DC Converter Typical Characteristics
Loop Crossover Gain and Phase
16 12 8
AAT1154
Transient Response
(IOUT = 0 to 3.0A; VOUT = 3.3V; VIN = 5.0V)
180 135 90
100 0 3x 100F 6.3V Ceramic TDK P/N C3325X5R0J107M 7 6
120F 6.3V Tantalum Vishay P/N 594D127X96R3C2T Phase
Phase (degrees)
Inductor Current (bottom) (A)
Gain (dB)
4 0 -4 -8 -12 -16 10000
45 0
Output Voltage (top) (mV)
-100 -200 -300 -400 -500 -600 -700 0 100 200 300 400
5 4 3 2 1 0 -1 500
Gain
-45 -90 -135 -180 100000
Frequency (Hz)
Time (s)
Transient Response
(IOUT = 0 to 3.0A; VOUT = 3.3V; VIN = 5.0V)
100 0 2x 100F 6.3V Ceramic TDK P/N C3325X5R0J107M 7 6
Tantalum Transient Response
(IOUT = 0 to 3.0A; VOUT = 3.3V; VIN = 5.0V)
100 0 7 6
Inductor Current (bottom) (A)
Inductor Current (bottom) (A)
Output Voltage (top) (mV)
Output Voltage (top) (mV)
-100 -200 -300 -400 -500 -600 -700 0 100 200 300 400
5 4 3 2 1 0 -1 500
-100 -200 -300 -400 -500 -600 -700 0 120F 6.3V Tantalum Vishay P/N 594D127X96R3C2T 100 200 300 400 500
5 4 3 2 1 0 -1
Time (s)
Time (s)
8
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter Functional Block Diagram
VCC VP = 2.7V to 5.5V
AAT1154
REF
FB
OP. AMP
CMP
DH
LOGIC
LX
OSC
Temp. Sensing
GND
EN
Applications Information
Main Control Loop
The AAT1154 is a peak current mode step-down converter. The inner wide bandwidth loop controls the inductor peak current. The inductor current is sensed as it flows through the internal P-channel MOSFET. A fixed slope compensation signal is then added to the sensed current to maintain stability for duty cycles greater than 50%. The inner loop appears as a voltage-programmed current source in parallel with the output capacitor. The voltage error amplifier output programs the current loop for the necessary inductor current to force a constant output voltage for all load and line conditions. The feedback resistive divider is internal, dividing the output voltage to the error amplifier reference voltage of 1V. The error amplifier has a limited DC gain. This eliminates the need for external compensation components, while still providing sufficient DC loop gain for good load regulation. The crossover frequency and phase margin are set by the output capacitor value. Duty cycle extends to 100% as the input voltage approaches the output voltage. Thermal shutdown protection disables the device in the event of a short-circuit or overload condition.
Soft Start/Enable
Soft start controls the current limit when the input voltage or enable is applied. It limits the current surge seen at the input and eliminates output voltage overshoot. When pulled low, the enable input forces the device into a low-power, non-switching state. The total input current during shutdown is less than 1A.
Power and Signal Source
Separate small signal ground and power supply pins isolate the internal control circuitry from switching noise. In addition, the low pass filter R1 and C3 (shown in Figure 1) filters noise associated with the power switching.
Current Limit and Over-Temperature Protection
Over-temperature and current limit circuitry protects the AAT1154 and the external Schottky diode during overload, short-circuit, and excessive ambient temperature conditions. The junction over-temperature threshold is 140C nominal and has 15C of hysteresis. Typical graphs of the over-temperature load current vs. input voltage and ambient temperature are shown in the Typical Characteristics section of this document. 9
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter
VIN 3.5V to 5.5V VOUT 3.3V @ 3A U1 AAT1154-3.3 FB VP L1 1.5H
+ -
AAT1154
C4 100F
R1 100
R2 100k
GND LX EN C1 10F C3 0.1F LX
VCC VP
D1 B340LA
C2 120F
rtn
C1 Murata 10F 6.3V X5R GRM42-6X5R106K6.3 C2 Vishay120F 6.3V 594D127X96R6R3C2T C3 0. F 0603ZD104M AVX 1 C4 Vishay Sprague 100F 16V 595D107X0016C 100F 16V D1 B340LA Diodes Inc. L1 CDRH6D28-1.5H Sumida Options C2 MuRata 100F 6.3V GRM43-2 X5R 107M 100F 6.3V (two or three in parallel) C2 TDK 100F 6.3V C3325X5R0J107M 100F 6.3V (two or three in parallel)
Figure 1: 3.3V, 3A Output.
Inductor
The output inductor is selected to limit the ripple current to 20% to 40% of full load current at the maximum input voltage. Manufacturer's specifications list both the inductor DC current rating, which is a thermal limitation, and the peak current rating, which is determined by the inductor saturation characteristics. The inductor should not show any appreciable saturation under normal load conditions. During overload and short-circuit conditions, the inductor can exceed its peak current rating without affecting converter performance. Some inductors may have sufficient peak and average current ratings yet result in excessive losses due to a high DC resistance (DCR). The losses associated with the DCR and its effect on the total converter efficiency must be considered. For a 3A load and the ripple current set to 30% at the maximum input voltage, the maximum peak-to-peak ripple current is 0.9A. Assuming a 5V 5% input voltage and 30% ripple, the output inductance required is:
L =I =
OUT
VOUT VOUT * k * FS * 1 - VIN(MAX)
3.3V * 1 - 3.3V 3A * 0.3 * 1MHz 5.25V
= 1.36H
The factor "k" is the fraction of the full load (30%) selected for the ripple current at the maximum input voltage. The corresponding inductor RMS current is:
IRMS = 2 I 2 I+ I O = 3A O 12
I is the peak-to-peak ripple current which is fixed by the inductor selection above. For a peak-to-peak current of 30% of the full load current, the peak current at full load will be 115% of the full load. The 1.5H inductor selected from the Sumida CDRH6D38 series has a 11m DCR and a 4.0A DC current rating with a height of 4mm. At full load, the inductor DC loss is 99mW for a 1% loss in efficiency.
10
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter
Schottky Freewheeling Diode
The Schottky average current is the load current multiplied by one minus the duty cycle. For VIN at 5V and VOUT at 3.3V, the average diode current is:
V 3.3V = 1A I AVG = IO * 1 - O = 3A * 1 VIN 5.0V
AAT1154
and the output voltage. It is highest when the input voltage is double the output voltage where it is one half of the load current.
IRMS = IO * VO V * 1- O VIN VIN
With a 125C maximum junction temperature and a 120C/W thermal resistance, the maximum average current is:
IAVG = T J(MAX)- T AMB = 125C - 70C = 1.14A 120 C/ W * 0.4V
A high ESR tantalum capacitor with a value about 10 times the input ceramic capacitor may also be required when using a 10F or smaller ceramic input bypass capacitor. This dampens any input oscillations that may occur due to the source inductance resonating with the converter input impedance.
JA * VFWD
Output Capacitor
With no external compensation components, the output capacitor has a strong effect on loop stability. Larger output capacitance will reduce the crossover frequency with greater phase margin. A 200F ceramic capacitor provides sufficient bulk capacitance to stabilize the output during large load transitions and has ESR and ESL characteristics necessary for very low output ripple. The RMS ripple current is given by:
IRMS = (VOUT + VFWD) * (VIN - VOUT) L * FS * VIN 2* 3 * 1
For overload, short-circuit, and excessive ambient temperature conditions, the AAT1154 enters overtemperature shutdown mode, protecting the AAT1154 and the output Schottky. In this mode, the output current is limited internally until the junction temperature reaches the temperature limit (see over-temperature characteristics graphs). The diode reverse voltage must be rated to withstand the input voltage. 3A Surface Mount Schottky Diodes
Diodes Inc. ROHM Micro Semi B340LA RB050L-40 5820SM 0.45V @ 3A 0.45V @ 3A 0.46V @ 3A
Input Capacitor Selection
The primary function of the input capacitor is to provide a low impedance loop for the edges of pulsed current drawn by the AAT1154. A low ESR/ESL ceramic capacitor is ideal for this function. To minimize stray inductance, the capacitor should be placed as closely as possible to the IC. This also keeps the high frequency content of the input current localized, minimizing the radiated and conducted EMI while facilitating optimum performance of the AAT1154. Proper placement of the input capacitor C1 is shown in the layout in Figure 2. Ceramic X5R or X7R capacitors are ideal. The size required will vary depending on the load, output voltage, and input voltage source impedance characteristics. Typical values range from 1F to 10F. The input capacitor RMS current varies with the input voltage
For a ceramic output capacitor, the dissipation due to the RMS current and associated output ripple are negligible. Tantalum capacitors with sufficiently low ESR to meet output ripple requirements generally have an RMS current rating much greater than that actually seen in this application. The maximum tantalum output capacitor ESR is:
ESR
VRIPPLE I
where I is the peak-to-peak inductor ripple current. Due to the ESR zero associated with the tantalum capacitor, smaller values than those required with ceramic capacitors provide more phase margin with a greater loop crossover frequency.
1154.2006.09.1.6
11
1MHz 3A Step-Down DC/DC Converter
AAT1154
Figure 2: AAT1154 Fixed Output Top Side Layout.
Figure 3: AAT1154 Fixed Output Bottom Side Layout.
Layout
Figures 2 and 3 display the suggested PCB layout for the fixed output AAT1154. The following guidelines should be used to help ensure a proper layout. 1. The connection from the input capacitor to the Schottky anode should be as short as possible. 2. The input capacitor should connect as closely as possible to VP (Pins 5 and 8) and GND (Pin 2). 3. C1, L1, and CR1 should be connected as closely as possible. The connection from the cathode of the Schottky to the LX node should be as short as possible. 4. The feedback trace (Pin 1) should be separate from any power trace and connect as closely as possible to the load point. Sensing along a high-current load trace can degrade DC load regulation. 5. The resistance of the trace from the load return to GND (Pin 2) should be kept to a minimum. This will help to minimize any error in DC regulation due to differences in the potential of the internal reference ground and the load return. 6. R1 and C3 are required in order to provide a cleaner power source for the AAT1154 control circuitry.
P = I RMS2 * RDS(ON) ON
RDS(ON) losses
IRMS =
2 2 I IO + *D 12
Internal switch RMS current D is the duty cycle and VF is the forward drop of the Schottky diode.
D=
VO + VF VIN + VF
I is the peak-to-peak inductor ripple current. A simplified form of calculating the RDS(ON) and switching losses is given by:
P=
I O 2 * R DS(ON) VO + tSW * FS * IO + IQ * VIN VIN
where IQ is the AAT1154 quiescent current. Once the total losses have been determined, the junction temperature can be derived. The thermal resistance (JA) for the SOP-8 package mounted on an FR4 printed circuit board in still air is 110C/W. TJ = P * JA + TAMB TAMB is the maximum ambient temperature and TJ is the resultant maximum junction temperature.
Thermal
The losses associated with the AAT1154 output switching MOSFET are due to switching losses and conduction losses. The conduction losses are associated with the RDS(ON) characteristics of the output switching device. At the full load condition, assuming continuous conduction mode (CCM), an accurate calculation of the RDS(ON) losses can be derived from the following equations: 12
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter
Design Example
(See Figures 1 and 4 for reference) IOUT IRIPPLE VOUT VIN FS TMAX 3A 30% of Full Load at Max VIN 3.3V 5V 5% 1MHz 70C
P= ON =
AAT1154
AAT1154 Junction Temperature
IO2 * RDS(ON) * VO tSW * FS * IO + IQ * VIN = + VIN 2
32 * 65m * 3.3V 20ns * 1MHz * 3A + + 750 A 5V 2
= 0.539 Watts
TJ(MAX)= TAMB + JA * P = 70C + 110C / W * 0.54W = 129C
Inductor Selection
L= =
VOUT V * 1 - OUT IO * k * FS VIN
Diode
V IDIODE= IO * 1 - O VIN 3.3V = 3A * 1 = 1.02A 5V
VF = 0.35 V
3.3V 3.3 V * 1= 1.25H 3A * 0.3 *1MHz 5V
Use standard value of 1.5H Sumida Inductor Series CDRH6D38.
I = =
VO V 1- O VIN L * FS 3.3V 3.3V 1= 0.82A 1.5H * 1MHz 5.25V
I 2
PDIODE * VF * IDIODE
0.35V * 1.01A = 0.354W
Given an ambient thermal resistance of 120C/W from the manufacturer's data sheet, TJ(MAX) of the diode is:
I PK = IOUT +
= 3A + 0.41A = 3.41A
T J(MAX) = T AMB + JA * P = 70C + 120C / W * 0.354W = 112C
Efficiency vs. Load Current
(VIN = 5V; VOUT = 3.3V)
100 95
Efficiency (%)
90 85 80 75 70 65 60 0.01 0.1 1 10
Output Capacitor
The output capacitor value required for sufficient loop phase margin depends on the type of capacitor selected. For a low ESR ceramic capacitor, a minimum value of 200F is required. For a low ESR tantalum capacitor, lower values are acceptable. While the relatively higher ESR associated with the tantalum capacitor will give more phase margin and a more dampened transient response, the output voltage ripple will be higher.
Output Current (A)
Figure 4: 5V Input, 3.3V Output.
1154.2006.09.1.6
13
1MHz 3A Step-Down DC/DC Converter
The 120F Vishay 594D tantalum capacitor has an ESR of 85m and a ripple current rating of 1.48Arms in a C case size. Although smaller case sizes are sufficiently rated for this ripple current, their ESR level would result in excessive output ripple. The ESR requirement for a tantalum capacitor can be estimated by: In the examples shown, C1 is a ceramic capacitor located as closely to the IC as possible. C1 provides the low impedance path for the sharp edges associated with the input current. C4 may or may not be required, depending upon the impedance characteristics looking back into the source. It serves to dampen out any input oscillations that may arise from a source that is highly inductive. For most applications, where the source has sufficient bulk capacitance and is fed directly to the AAT1154 through large PCB traces or planes, it is not required. When operating the AAT1154 evaluation board on the bench, C4 is required due to the inductance of the wires running from the laboratory power supply to the evaluation board.
AAT1154
ESR
IRMS = =
VRIPPLE 100 mV = = 121 m I 0.82A
1 *
(VOUT + VF) * (VIN - VOUT) L * FS * VIN 2* 3
3.65V *1.7 V = 240mArms 2 * 3 1.5H * 1MHz * 5V 1 *
Adjustable Output
For applications requiring an output other than the fixed outputs available, the 1V version can be externally programmed. Resistors R3 and R4 of Figure 5 force the output to regulate higher than 1V. For accurate results (less than 1% error for all outputs), select R4 to be 10k. Once R4 has been selected, R3 can be calculated. For a 1.25V output with R4 set to 10k, R3 is 2.5k. R3 = (VO - 1) * R4 = 0.25 * 10k = 2.5k Figures 6 and 7 display the suggested PCB layout for the adjustable output AAT1154.
Two or three 1812 X5R 100uF 6.3V ceramic capacitors in parallel also provide sufficient phase margin. The low ESR and ESL associated with ceramic capacitors also reduces output ripple significantly over that seen with tantalum capacitors. Temperature rise due to ESR ripple current dissipation is also reduced.
Input Capacitor
The input capacitor ripple is:
IRMS = I O *
V V O * 1 - O = 1.42 Arms VIN VIN
VIN 2.7V to 5.5V
VOUT 1.25V @3A R3 2.55k U1 AAT1154-1. 0 FB VP L1 1.5H
C4 100F
R1 100
R2 100k
GND LX EN C1 10F C3 0.1F R4 10.0k LX
VCC VP
D1 B340LA
C2 120F
rtn
C1 Murata 10F 6.3V X5R GRM42-6X5R106K6.3 C2 Vishay 120F 6.3V 594D127X96R6R3C2T C3 0. F 0603ZD104M AVX 1 C4 Vishay Sprague 100F 16V 595D107X0016C 100F 16V D1 B340LA Diodes Inc. L1 CDRH6D28-1.5H Sumida Options C2 MuRata 100uF 6.3V GRM43-2 X5R 107M 100F 6.3V (two or three in parallel) C2 TDK 100F 6.3V C3325X5R0J107M 100F 6.3V (two or three in parallel)
Figure 5: AAT1154 Evaluation Board With Adjustable Output. 14
1154.2006.09.1.6
1MHz 3A Step-Down DC/DC Converter
AAT1154
Figure 6: Evaluation Board Adjustable Output Top Side Layout.
Figure 7: Evaluation Board Adjustable Output Bottom Side Layout.
Capacitors Part Number
C4532X5ROJ107M GRM43-2 X5R 107M 6.3 GRM43-2 X5R 476K 6.3 GRM42-6 X5R 106K 6.3 594D127X_6R3C2T 595D107X0016C
Manufacturer
TDK MuRata MuRata MuRata Vishay Vishay
Capacitance (F)
100 100 47 10 120 100
Voltage (V)
6.3 6.3 6.3 6.3 6.3 16.0
Temp Co.
X5R X5R X5R X5R
Case
1812 1812 1812 1206 C C
Inductors Part Number
CDRH6D38-4763-T055 N05D B1R5M NP06DB B1R5M LQH55DN1R5M03 LQH66SN1R5M03
Manufacturer
Sumida Taiyo Yuden Taiyo Yuden MuRata MuRata
Inductance (H)
1.5 1.5 1.5 1.5 1.5
I (Amps)
4.0 3.2 3.0 3.7 3.8
DCR ()
0.014 0.025 0.022 0.022 0.016
Height (mm)
4.0 2.8 3.2 4.7 4.7
Type
Shielded Non-Shielded Shielded Non-Shielded Shielded
Diodes Manufacturer
Diodes Inc. ROHM Micro Semi
Part Number
B340LA RB050L-40 5820SM
VF
0.45V @ 3A 0.45V @ 3A 0.46V @ 3A
1154.2006.09.1.6
15
1MHz 3A Step-Down DC/DC Converter Ordering Information
Output Voltage
1.0V (Adj. VOUT 1.0V) 1.8V 2.5V 3.3V
AAT1154
Package
SOP-8 SOP-8 SOP-8 SOP-8
Marking
115410 115418 115425 115433
Part Number (Tape and Reel)1
AAT1154IAS-1.0-T1 AAT1154IAS-1.8-T1 AAT1154IAS-2.5-T1 AAT1154IAS-3.3-T1
All AnalogicTech products are offered in Pb-free packaging. The term "Pb-free" means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree.
Package Information
SOP-8
3.90 0.10
4.90 0.10
6.00 0.20
0.375 0.125
45
1.55 0.20
0.175 0.075
4 4
0.235 0.045 0.825 0.445
0.42 0.09 x 8
1.27 BSC
All dimensions in millimeters.
1. Sample stock is generally held on part numbers listed in BOLD.
(c) Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech's standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders.
Advanced Analogic Technologies, Inc.
830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 16
1154.2006.09.1.6

▲Up To Search▲

Price & Availability of AAT1154IAS-10-T1

	To Download AAT1154IAS-10-T1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .